48A Tesla Wall Connector Wire Size at 100 Feet
At 100 ft the 48 A Wall Connector still uses 60 A for ampacity. The longer one-way run is what pushes the voltage-drop check.
Formula SSC-2026.1
K method · SSC-2026.1
Minimum size
6 AWG · 13.3 mm²
Single conductor set
Voltage drop
4.72 V
1.97% · end 235.3 V
Power loss
227 W
I²R at the operating current
Required ampacity
60.0 A
Each conductor 65 A
Material estimate
$796.00
3 conductors + EMT
Conductor weight
29.4 lb
13.3 kg · approximate insulated weight
Circle diameters track circular mils. The drawing is a schematic, not a conduit-fill layout.
| Item | Net | Waste | Order | Unit price | Line total |
|---|---|---|---|---|---|
| copper 6 AWG · 13.3 mm² | 100 ft one way | cuts excluded | 3 conductors | USD | $611.00 |
| EMT conduit | 100 ft | — | 100 ft | USD | $185.00 |
| Material | Minimum size | mm² | Drop | End voltage | Loss |
|---|---|---|---|---|---|
| copper | 6 AWG · 13.3 mm² | 13.3 | 1.97% | 235.3 V | 227 W |
| aluminum | 4 AWG · 21.2 mm² | 21.2 | 2.03% | 235.1 V | 234 W |
| Distance | Minimum size | Drop | Percent | End voltage |
|---|---|---|---|---|
| 75 ft | 6 AWG · 13.3 mm² | 3.54 V | 1.47% | 236.5 V |
| 100 ft | 6 AWG · 13.3 mm² | 4.72 V | 1.97% | 235.3 V |
| 125 ft | 6 AWG · 13.3 mm² | 5.90 V | 2.46% | 234.1 V |
Show the deterministic formula
Single phase: Vdrop = 2 × K × I × D / cmil. Three phase: Vdrop = 1.732 × K × I × D / cmil. K is 12.9 for copper and 21.2 for aluminum. D is one-way feet.
Percent drop = Vdrop ÷ source voltage × 100. Green is 3% or less, amber is 3 to 5%, and red is over 5%. Power loss is I²R on the current-carrying conductors.
The smallest conductor that meets both the ampacity (125% when continuous) and the drop limit is selected. Ampacity does not include bundling or temperature correction.
Contractor sign-off
Project: 48A Tesla Wall Connector Wire Size at 100 Feet
Prepared by
Date
Verified by (PE / electrician / inspector)
License number
Signature
This sheet is an estimate for ordering and layout discussion. It is not a sealed design. Confirm the quantities with a licensed local professional and the authority having jurisdiction before you buy or build.
Engineering notes
At 100 ft the 48 A Wall Connector still uses 60 A for ampacity. The longer one-way run is what pushes the voltage-drop check. The run is 100 ft one way at 48 A on 1ph-240. K is 12.9 for copper and 21.2 for aluminum. Ambient temperature, bundling, and rooftop adders are not applied.
Code reference
NEC 210.19(A) and 215.2(A) informational notes recommend 3 percent on a branch circuit and 5 percent total with the feeder. Ampacity follows the 75°C column of Table 310.16 plus the small-conductor limits. Confirm the adopted edition.
Field questions
- What current is used for the 48 A voltage drop?
- Voltage drop uses the operating amps. Ampacity uses 125 percent because the load is marked continuous.
- Does this replace the equipment installation manual?
- No. The nameplate, the breaker, and the adopted NEC edition still control. This page is the K-method size and the percent drop.
- Can I switch copper and aluminum?
- Yes. The conductor control and the comparison table both recompute size, drop, and the planning cost.
Explore Related Engineering Calculations
- 50 Amp EV Charger Wire Size at 50, 75, and 100 Feet
- 100 Amp Subpanel Feeder: Copper vs Aluminum
- 30 Amp RV Outlet Wire Gauge and Voltage Drop
- 200 Amp Main Service Entrance Wire Size
- 240 V Mini-Split Heat Pump Wire Gauge
- 60 Amp Detached Garage Subpanel Wire Size
- 20×20 Garage Slab: 4 Inch vs 6 Inch
- Deck Stair Stringer Calculator, 36 to 96 Inch Rise
- 6/12 Roof Pitch, Rafter Length, and Shingle Bundles
- 20 ft dry, US 48×40 pallets: Pallet Count, CBM, and Payload